Wheeled Tractor Maintenance Points
Wheeled (Crawler) Tractor Maintenance Technical Points
(I) Engine
1. Check the lubrication system. In addition to replacing the three cores (air filter element, diesel filter element, oil filter element), replace or clean each hydraulic oil filter element. Lubricating oil and fuel should be replaced according to regional and seasonal requirements. If the lubricating oil has been released, the oil filler on the cylinder head should be opened, after adding qualified lubricating oil, let it stand for ten minutes, check the oil dipstick, it should be flush with the "upper" line of the oil dipstick, and then let it stand for 20~30 minutes to check whether the oil level has changed. If there is an increase, find the cause and troubleshoot. If it is an engine with a turbocharger, you need to remove the hollow bolt of the oil inlet of the turbocharger suspension bearing, drop a few drops of lubricating oil, and install it again. The grease nipple and oil cup shall be complete. All lubricating parts and assemblies shall be filled with enough lubricating oil or grease according to the specified oil. The ventilator shall be clean and unblocked.
2. Check the cooling system. Clean up the sundries on the surface of the radiator and fan, check the radiator and connecting hose to ensure no leakage (water); check and adjust the tightness of the fan belt to meet the specified requirements. Fill up the coolant (water) and let it stand for one hour to see if the liquid level changes. If the liquid level drops, you need to find the reason; if not, it is normal. Pay attention not to add well water and tap water that are easy to produce scale.
3. Check the electrical system. The circuits of starting, lighting and instrument shall be normal, and the insulation parts of all electrical accessories shall be free of leakage and short circuit. The cold start device of the engine in cold area shall work normally. When the battery is low, it should be charged with one tenth of the rated current of the battery. When charging the lead-acid battery, the electrolyte level is flush with the engraved line or 10~15mm higher than the separator. Open the filling plug to prevent the outlet from being blocked and the battery explodes due to excessive air pressure. After charging is completed, the single battery voltage should be around 13 volts. After the above are checked to be normal, the main and auxiliary transmission handles should be in the "empty", "down", "middle" or "separated" position before starting; the hydraulic power device should be in the "middle" position; at this time, use the front end pulley of the crankshaft Turn the hole or open the small window on the flywheel housing for turning, turn the crankshaft 3~5 times, and then turn on the ignition switch, start the engine (for small and medium-sized tractors parked for more than 1 month). The engine speed needs to be low first and then high, and gradually increase. At the same time, observe the instrument and listen carefully to the sound. If there is any abnormality, stop the machine first and then check and troubleshoot.
(II)
1. Check the lubricating oil. Check the lubricating oil of the gearbox, front axle, and end drive one by one; check whether the lithium-based grease of the steering gear (worm gear mechanical steering gear) or the hydraulic oil tank (hydraulic steering gear) is sufficient; check the hydraulic oil of the hydraulic system Whether the oil is sufficient.
2. Check the steering system. Pay attention to the clearance between the left and right directions, and observe the clearance between the rod ball end drive and the pin shaft of the oil cylinder (hydraulic cylinder direction). If the clearance is too large, replace the rod ball end and the pin shaft of the oil cylinder. After replacing the ball head and pin shaft, check the toe. The toe of the four-wheel drive is 0~4mm, and the toe of the two-wheel drive is 5~10mm.
3. Check the clutch. Check the gap between the clutch pedal and the release bearing and the release lever to ensure thorough and flexible separation without jamming. When the pedal stroke is 4/5, the shift position can be hung without abnormal noise. If the clutch has been used for too long, it is necessary to disassemble and check the friction plate and release bearing. If the limit is exceeded, replace it; if the wear is not large, add grease to the release bearing and then assemble it according to the standard.
4. Check the brake. Check the brake fluid level and pedal stroke. The first foot of the brake pedal can be pressed to death at one time, and the second foot cannot be pressed continuously. The return is normal and there is no seizure. The heights of the left and right brake pedals should be synchronized.
5. Track-type tractor Check the connection between the gearbox and the rear axle, the universal joint, the support trolley, and the fastening of the frame and the rear axle, and check whether the tension of the track meets the specified requirements. If not, it should be adjusted.
(III) and farm tools
1. Adjust the upper pull rod (central pull rod) and left and right suspenders of the tractor to make the farm tool rack horizontal in both longitudinal and transverse directions.
2. Adjust the limit screw of the lower suspension arm of the tractor to make the transverse center line of the farm implement coincide with the longitudinal center line of the tractor. The pin shaft connecting the tractor suspension pull-down rod and the left and right hanger rods is placed at the position of the long hole, so that the overall profiling effect can be achieved when the farm tools work.
3. The selected drive shaft shall be matched with the tractor PTO spline, and the matching length shall not be less than 200mm. The angle between the transmission shaft and the power output shaft is preferably less than 10 degrees, and it is strictly forbidden to exceed the maximum working angle specified by the agricultural implement. The cross shaft and bearing of the transmission shaft shall not be loose, and the rotation shall be flexible in all directions, and grease shall be added.
Source: Public Number Sangma Words Liangzhou
Website: https://mp.weixin.qq.com/s/ZTSndPLw1mcZo3Bfs2hvUA
