Overhaul points of turning plough
turning ploughMaintenance to bepoint
Maintenance before (I) operation
1. Check the parts such as ploughshare and ploughshare wall. If the thickness of ploughshare blade is greater than 3mm, it shall be polished, repaired or replaced, and if the ploughshare wall is seriously worn, it shall be replaced.
2. Check that the local tire pressure is within the normal range (if any).
3. Check all kinds of bolts, nuts and pin shafts to ensure that they are in a tight state. Among them, the fixing bolts of the plow wall cannot be too tight to prevent the plow wall from generating stress and easily breaking.
4. Check each lubrication port to ensure sufficient butter. Lubricate the movable parts (axle, walking crank, etc.) with oil.
5. After the turning plow is connected with the matching tractor, a safety lock pin should be installed; check the hydraulic oil pipe to prevent oil leakage and oil pipe entanglement.
6. Lift the plow, adjust the lifting speed, check the longitudinal stability of the tractor, and add counterweight to the tractor if necessary.
7. Operate the tractor to check whether the turning plow is normal.
(II) operation
1. Adjustment of penetration angle. Loosen the fastening bolts and positioning adjustment bolts connected between the plow body and the plow column, and then tap the plow body to slightly change the angle of the plow body relative to the plow column to increase or decrease the soil entry angle. The soil penetration angle should be 3 to 10 degrees. The more plows, the smaller the soil penetration angle. After adjustment, the plow tips of the same side of the plow body shall be at the same height, and the fastening bolts and positioning adjustment bolts shall be tightened.
2. Tillage depth adjustment. Under normal circumstances, the tillage depth of the turning plough is 20~40cm. In trial tillage, if the tillage depth is too deep or too shallow, the depth limiting wheel should be adjusted. Turn the adjusting bolt (handle) of the depth limiting wheel, lower the depth limiting wheel, raise the plow frame, reduce the plowing depth, and turn the adjusting bolt in the opposite direction to increase the plowing depth. The tillage depth can also be adjusted by the tractor hydraulic system to meet the requirements. Refer to the tractor manufacturer's operating instructions for the setting of the tractor hydraulic system. At this time, the tractor hydraulic system must be adjusted to force adjustment or force and position comprehensive adjustment.
3. Horizontal adjustment. When the tractor stops on the horizontal ground, the suspension frame beam (plow frame) should be parallel to the ground. If the parallel cannot be maintained, the two pull rods of the tractor should be adjusted to be at the same height. When ploughing, the plow column should be as vertical as possible to the ground as viewed from the direction of travel. If vertical cannot be maintained, the horizontal level of the beam shall be adjusted by means of horizontal adjustment bolts on both sides of the suspension beam. Use the same method to keep the other side parallel to the ground.
4. Longitudinal horizontal adjustment. After the horizontal adjustment is completed, the plow frame will be adjusted vertically in the trial tillage. The adjustment is limited to the adjustment of the upper pull rod of the tractor suspension mechanism. If the plow frame is high in front and low in back, it is difficult to enter the soil or the ploughing depth is too shallow, the upper pull rod should be shortened; otherwise, the upper pull rod should be extended.
5. The first plow operating width adjustment. Adjust the working width of the first plow body by adjusting the lead screw, so that the width of the soil cut by the first plow body is the same as the width of the soil cut by the other plow body, and is flat with the soil seam.
6. Tow line adjustment. When the tractor is obviously deviated during the trial operation, the traction line should be adjusted. Loosen the frame adjustment screw lock nut, adjust the length of the screw to make the turning plow traction line consistent with the direction of travel, and then lock the nut.
7. Observe the operation situation at any time during operation. If the machine is blocked or tangled with grass, clean it up in time.
(III) safety operation tips
1. When starting the operation, the plow body should be dropped while walking to avoid severe impact damage to the working parts.
2. It is strictly prohibited to take people on the turning plough during the operation. In case of abnormal noise, the operation shall be stopped in time, and the operation shall be continued after the cause is found out and solved.
3. When working on the ground, the plough should be lifted first, and the plough can only be turned after the plough is completely unearthed. It is strictly forbidden to lift while turning to avoid damage to the plough, plough post and tractor rear suspension system.
4. Do not transport long distances in a suspended state. During transportation, ensure that the limit rods on both sides of the lower pull rod of the tractor are locked, and it is strictly forbidden to carry heavy objects on the plow frame to avoid deformation of the plow frame. When passing through bumpy roads or gullies, you must slow down to avoid excessive bumpy impacts.
5. During maintenance or repair, ensure that the reliable support mechanism or hydraulic locking device reliably supports the hydraulic turning plow.
6. When the machine is shut down, the plow should be landed on the ground. When the turning plow is stored, the support rod should be used to support the plow frame to prevent it from overturning.
Source: Public Number Sangma Words Liangzhou
