Wheat Planter Maintenance Technical Points
Wheat Planter Maintenance Technical Points
(I) operation
1. Fastening and oiling. Before using the machine, check whether each fastening part is fastened firmly and whether each transmission part rotates flexibly. Add butter to the universal joint cross, knife shaft bearing seat and suppression wheel bearing seat, add gear oil to the gear box, add it to the lower middle position of the bevel gear, and add lubricating oil to the chain drive and other rotating parts.
2. Hanging of machines and tools. Method 1: Pull out the universal joint, install the two internal splines on the tractor and the planter respectively, and install the bolt. After the rear suspension of the tractor is basically aligned with the suspension device of the implement, connect the universal joint first, then install the lower suspension and the upper suspension, and insert the lock pin. Method 2: After the rear suspension of the tractor is basically aligned with the suspension device of the implement, first install the lower suspension and the upper suspension, and then install the two internal splines of the universal joint on the tractor and the planter respectively, and insert the lock pin. During the installation process, the gear shaft of the machine can be rotated with a slight force.
3. Adjustment of fertilizer drainers. The use of granular fertilizer, the amount of fertilizer should not be too large, otherwise it may produce the phenomenon of burning seedlings. First coarse adjustment: turn the fertilizer discharge adjustment handwheel until the seeding amount indication reaches the predetermined position. Re-fine adjustment: suspend the suppression wheel, rotate the suppression wheel, and after all the fertilizer is discharged from the fertilizer discharging device, rotate the suppression wheel at a constant speed according to the normal driving speed and direction, receive the fertilizer discharged from each row of fertilizer pipes, weigh the weight of the fertilizer discharged from each row of fertilizer pipes and the total weight of the fertilizer discharged, and calculate the average row fertilizer discharge and mu sowing rate of each row.
4. Adjustment of the seed meter. When sowing large grain crops such as wheat, first open the row of seed and seed-appropriate plate, and then adjust the amount of sowing. One is the method of adjusting the sowing quantity of the stepped gearbox, which realizes the adjustment of the sowing quantity by adjusting the gear of the gearbox. The second is the stepless gearbox seeding amount adjustment method, counterclockwise rotation handwheel seeding amount increases, clockwise rotation handwheel seeding amount decreases, the required seeding amount must be adjusted from small to large to the required position.
5. Limit of suppression wheel. The rocker arms on both sides of the suppression wheel are fixed by the limit pin of the sector plate, and the limit pin must be placed in the appropriate hole position on the sector plate during operation.
6. Adjustment of left and right level of machines and tools. Raise the machine and make the rotary knife and the furrow opener leave the ground. Check whether the blade tip of the rotary knife, the furrow opener and the machine are in the same level. If not, adjust the rear suspension diagonal pull rod of the tractor.
7. Inspection of rotational clearance. Before operation, check and ensure that the rotation clearance between the rotating knife and the opener is ≥ 1cm. Ensure that the rotary cutter does not collide with the opener during operation.
(II) operation
1. Before and after the horizontal adjustment of the machine. During operation, the front and back of the machines and tools should be in the same horizontal plane. At this time, the included angle between the universal joint and the horizontal plane of the machines and tools should be within the range of ± 10 °, otherwise the upper pull rod of the tractor should be adjusted.
2. Adjustment of sowing and fertilizing depth. The first is to change the length of the upper pull rod of the rear suspension of the tractor and the position of the limit pins on the rocker arms on both sides of the two sets of suppression wheels, which can simultaneously change the depth of sowing and fertilization, and the depth of tillage. The second is to change the installation height of the seed and fertilizer opener, and the depth of sowing and fertilization can be adjusted, but the relative position of the depth of seed and fertilizer remains unchanged.
3. Adjustment of the ballast. According to agronomic requirements, the position of the limit pin on the rocker arm on both sides of the suppression wheel is changed at the same time to realize the adjustment of the ballast pressure. The lower the limit pin moves, the greater the ballast pressure.
4. During the operation, the straw and clay wound by the seed and fertilizer opener shall be cleaned frequently, the fertilizer discharge pipe and seed discharge pipe shall be checked for blockage, and the opener shall be deformed, and any faults found shall be eliminated in time.
(III) safety operation tips
1. The machine must be lifted when turning and reversing on the ground.
2. No one is allowed to stand on the planter during the operation of machines and tools.
3. When the maintenance personnel need to enter the lower part of the lifting machine during the maintenance of the machine tool, there should be reliable hard support to avoid the failure of the hydraulic mechanism and the injury to the maintenance personnel.
4. During the operation of machines and tools, it is strictly prohibited to approach rotating parts such as power output shaft to avoid the danger of twisting.
Source: Sangma dialect Liangzhou
Website: https://mp.weixin.qq.com/s/9sL-A8wJsiq-Yb28ynqkag
