Corn Harvester
Corn Harvester
corn combine harvester are as follows:
1. pick roll jam
encounter this situation usually take the following measures:
1. Slow down.
2. Appropriate small tool clearance.
3. Adjust the clearance of the pick roll.
4. Check if the pinch chain is functioning properly.
5. The spring force of the safety spring of the tassel box is not enough, and the pre-compression length of the spring is properly compressed to improve the elastic force.
2. machine vibration is too large
1. Check whether the drive shaft is bent and straighten the drive shaft.
2. Check whether the cross bearing is damaged and replace the bearing.
3. The damage or loss of the cutter blade will also cause the machine to vibrate too much, and it should be installed in time.
3. pinch chain does not turn
1. Adjust the distance between the tooth and the ground.
2. Check whether the screw rod of the spindle head of the double reel is loose, and adjust the spring preloading length.
3. If the pinch chain is too loose, adjust the tension of the pinch chain.
4. Check whether the upper and lower sprockets of the reel are wrapped with grass.
5. Check whether the friction plate is damaged. If it is damaged, replace it in time.
4. chopper rotor entangled
1. If the belt is too loose, adjust the belt tension.
2. The blade is accurate, and the distance between the blade and the ground shall not be less than 30mm.
5. peeler clogged
1. Adjust the tight spring.
2. adjust the transmission belt in short supply.
3. Adjust the high and low position of the pressure feeder.
4. Check whether the rubber plate of the pressure feeder is aging and broken, and should be replaced in time.
6. Lift Chain Inoperative
1. Check whether the belt is too loose and tighten the belt.
2. There are fruit ears stuck between the stem row rollers, which should be removed in time.
7. elevator inoperative
1. It is possible that the ear falls into the arc-shaped plate, and the ear should be cleaned in time.
2. Check whether the ear is brought under the partition and should be reversed.
3. If the drive belt is too loose, tension the belt.
8. missing or poor quality
1. Line spacing does not meet the requirements or walking deviation, should be operated.
2. Whether the belt is slipping, tension the belt.
3. Whether the blade is damaged or lost, it should be replaced or filled in time.
4. Reduce the forward speed appropriately.
9. peeling effect is poor
1. Adjust the pair of peeling roller gap.
2. Whether the peeling roller is wound with sundries shall be cleaned in time.
3. If the nail tooth is too low or falls off, the nail tooth should be adjusted or supplemented.
10. fruit weight ear grain loss too much
1. If the ground head turns too early, the elevator should be transported before turning.
2. If the clearance of the pick roller is too large, the clearance should be adjusted.
Effective Method to Reduce Sudden Failure of Corn Combine Harvester
, during the harvest season, some combine harvesters were forced to stop for repair due to sudden failures, which not only lost the best operating time, but also brought economic losses to the operators. Here to introduce several kinds of sudden failure when the effective solution:
For the sudden failure of the combine harvester, as long as scientific preventive measures are taken, the failure can be eliminated in the bud in time. In daily maintenance, the machine can maintain a good technical condition through three methods: daily maintenance, regular maintenance and seasonal maintenance.
Daily maintenance is carried out before and after the operation, which is easy to operate and can be completed without disassembling main parts. It is mainly to remove sediment, grass and dust from the outside of the machine; check whether diesel oil, lubricating oil, etc. are sufficient, whether there is water leakage or oil leakage, add lubricating oil to each part according to regulations; check and adjust the tightness of transmission parts, etc.
regular maintenance according to the working time to determine the maintenance cycle and content. In addition to completing the daily maintenance content, the maintenance content should also be inspected, replaced, and adjusted in time for some vulnerable parts in accordance with the regulations of regular maintenance to eliminate hidden troubles and ensure that the machine is in good technical condition.
Seasonal maintenance After the harvest is over, the machine needs a technical maintenance before it is parked for a long time. In the maintenance, first of all to remove the grain, grass, sand and other debris on the machine, to achieve clean, clean. The second is to carefully carry out maintenance according to the daily maintenance and regular maintenance requirements, and repair the parts with serious wear and deformation without "disease" parking. At the same time, it is necessary to do a good job in anti-rust, anti-freezing, fire prevention, anti-corrosion, anti-deformation, anti-theft, etc., to ensure that the machine can be put into use smoothly when it is activated again.
Website: https://mp.weixin.qq.com/s/mulGYQI9hYhoMISK5lwISg
