Created on:2025-09-11

Corn Ear Harvester Maintenance Guide

corn ear harvestmachineMaintenance Guide

Maintenance before (I) operation

Clean the air filter air duct, replace the oil filter element and diesel filter element, and replace the hydraulic oil, hydraulic oil, and brake fluid; fill the fuel tank with qualified diesel; check the cooling water and add coolant; check the battery power and charge; shake the engine The crankshaft rotates for 10 revolutions, and then start idling for 10 - 15 minutes if there is no abnormality; observe whether there is any abnormality.

check the picking table. Check whether the picking blade is intact, whether the blade is firm, whether the picking gap and the grass cutter gap are reasonable, and adjust the fastening as needed.

Check the peeling machine. Adjust the peeling roller gap, the peeling roller and the wheel pressure roller gap in turn, and adjust the threshing gap according to the operation requirements.

check or turn the part. Check the dynamic balance weight; check the tightness of the chain and the adhesive tape, and check whether the transmission adhesive tape is too long or has other abnormalities, and replace them all. In the radial clearance ≤ 0.2mm, the matching radial clearance ≤ 0.3mm, and the axial matching radial clearance ≤ 0.2mm.

Check the operating mechanism. Check whether the clutch, safety clutch and brake device are reliable, flexible and adjust as required.

check the hydraulic system. Check the hydraulic oil pump, control valve and pipeline, and replace those with serious internal leakage. Damaged should be removed or replaced in a timely manner; dirty hydraulic oil and impurities should be replaced.

check tightness. Check the joint between the conveying chute of the header of the picking table and the conveying chain, and check the tightness of the joint between the main conveying roller of the peeling machine and the ear box.
(II) operation

Check the leakage of each pipeline frequently, and repair it immediately after it is found.

Clean up the debris around the hydraulic pipeline and engine exhaust pipe in time to eliminate fire hazards.

, attention should be paid to the inspection and adjustment of the picking device according to the number of grains on the field and the ground and the breakage of stems.

After each shift is completed, it is necessary to thoroughly clean the instructions for shift maintenance, clean the filter element and transmission tension of the machine, lubricate all parts according to the instructions, and add lubricating oil to all parts.

prepare harvester accessories and wearing parts. According to the model, characteristics and usage of the machine, prepare the corresponding accessories and wearing parts, and get in touch with the enterprise after-sales service in time, and write down the contact address, telephone number and contact person.
(III) safety operation tips

, the overhaul, maintenance and use of the harvester should be done under the premise of ensuring safety.

When cleaning, cleaning, inspecting and maintaining the harvester, the engine must be turned off.

operator leaves the cab, the engine must also be shut down and the start key must be removed.

When starting the engine, you must honk the horn first to make sure that everyone else is away from the harvester before turning it on.

When two people repair and maintain the harvester together, it is strictly forbidden for another person to rotate the rotating parts without permission.

It is strictly forbidden to smoke in the field, and to prevent fire accidents caused by poor contact of electrical circuits, short circuit, and accumulation of grass debris around the engine exhaust pipe.


收获机械培训维修

Created on:2025-09-11

Corn Ear Harvester Maintenance Guide

corn ear harvestmachineMaintenance Guide

Maintenance before (I) operation

Clean the air filter air duct, replace the oil filter element and diesel filter element, and replace the hydraulic oil, hydraulic oil, and brake fluid; fill the fuel tank with qualified diesel; check the cooling water and add coolant; check the battery power and charge; shake the engine The crankshaft rotates for 10 revolutions, and then start idling for 10 - 15 minutes if there is no abnormality; observe whether there is any abnormality.

check the picking table. Check whether the picking blade is intact, whether the blade is firm, whether the picking gap and the grass cutter gap are reasonable, and adjust the fastening as needed.

Check the peeling machine. Adjust the peeling roller gap, the peeling roller and the wheel pressure roller gap in turn, and adjust the threshing gap according to the operation requirements.

check or turn the part. Check the dynamic balance weight; check the tightness of the chain and the adhesive tape, and check whether the transmission adhesive tape is too long or has other abnormalities, and replace them all. In the radial clearance ≤ 0.2mm, the matching radial clearance ≤ 0.3mm, and the axial matching radial clearance ≤ 0.2mm.

Check the operating mechanism. Check whether the clutch, safety clutch and brake device are reliable, flexible and adjust as required.

check the hydraulic system. Check the hydraulic oil pump, control valve and pipeline, and replace those with serious internal leakage. Damaged should be removed or replaced in a timely manner; dirty hydraulic oil and impurities should be replaced.

check tightness. Check the joint between the conveying chute of the header of the picking table and the conveying chain, and check the tightness of the joint between the main conveying roller of the peeling machine and the ear box.
(II) operation

Check the leakage of each pipeline frequently, and repair it immediately after it is found.

Clean up the debris around the hydraulic pipeline and engine exhaust pipe in time to eliminate fire hazards.

, attention should be paid to the inspection and adjustment of the picking device according to the number of grains on the field and the ground and the breakage of stems.

After each shift is completed, it is necessary to thoroughly clean the instructions for shift maintenance, clean the filter element and transmission tension of the machine, lubricate all parts according to the instructions, and add lubricating oil to all parts.

prepare harvester accessories and wearing parts. According to the model, characteristics and usage of the machine, prepare the corresponding accessories and wearing parts, and get in touch with the enterprise after-sales service in time, and write down the contact address, telephone number and contact person.
(III) safety operation tips

, the overhaul, maintenance and use of the harvester should be done under the premise of ensuring safety.

When cleaning, cleaning, inspecting and maintaining the harvester, the engine must be turned off.

operator leaves the cab, the engine must also be shut down and the start key must be removed.

When starting the engine, you must honk the horn first to make sure that everyone else is away from the harvester before turning it on.

When two people repair and maintain the harvester together, it is strictly forbidden for another person to rotate the rotating parts without permission.

It is strictly forbidden to smoke in the field, and to prevent fire accidents caused by poor contact of electrical circuits, short circuit, and accumulation of grass debris around the engine exhaust pipe.