Created on:2025-09-11

Self-walking Crawler Grain Combine Harvester Maintenance Points

self-walking crawler grain combine harvesterMaintenance points

Maintenance before (I) operation

1. Clean the engine air filter and air duct; clean or replace the oil filter element and diesel filter element and replace the oil pan oil, hydraulic oil, and brake fluid; fill the fuel tank with qualified diesel; add coolant; check the battery power And charge. Start the engine, idling for 10~15 minutes, and observe whether there is any abnormality. If there is any abnormality, stop the engine for inspection and elimination.

2. Check the bolt tightening of the roller, fan, header, screen box drive mechanism and other parts with high speed, heavy vibration and heavy load, and the sprocket and bearing with high speed, and adjust as required.

3. Check whether the rotating parts rotate flexibly; adjust the tension of the chain and transmission belt.

4. Inspect the harvesting mechanism. Check whether the cutter blade is intact and firm, whether the gap is reasonable, whether the center line of the moving blade and the blade protector is coincident, and adjust the fastening as required; adjust the height of the reel and the sagging amount of the holding claw according to the operation requirements.

5. Check the threshing and cleaning device. Adjust the threshing clearance and cleaning fan air volume according to the operation requirements. Check the wear of the grass cutter, vibrating screen and front bearing, louver sieve strip, etc. and replace them as necessary.

6. Check the straw handling mechanism. First, adjust the straw discharge position to ensure uniform discharge of straw when feeding the harvester. Second, check whether the cutting knife and fixed knife are worn or damaged, and replace with new blades if any. When the overlap between the cutter blade of the semi-feeding harvester and the supply knife blade is less than 9mm, the installation position of the supply knife shaft shall be adjusted. The gap between the cutter blade and the supply knife blade should be between 4.5~7mm; The gap between the straw chain pressure rod and the sprocket should be adjusted to within 2.5mm.

7. Check the technical status of clutches and brakes to see their reliability and flexibility.

8. Check the hydraulic oil pump, control valve and pipeline. If it is damaged, it should be replaced in time. If the hydraulic oil is too dirty and has impurities, it should be replaced.

9. Check the sealing of the joint between the bridge and the concave plate transition plate of the threshing roller to reduce the harvest loss and prevent the phenomenon of grain running and grain leakage.

(II) operation

1. The engine oil and oil filter must be replaced every 250 to 300 hours of operation, and the diesel filter must be replaced every 200 hours of operation; the hydraulic system must be replaced every 250 to 300 hours of operation. Oil change and oil return filter, walking filter element once. Be sure to shut down the engine before cleaning, overhaul, maintenance, refueling and before the operator leaves the cab.

2. Before lifting the header, opening the granary, threshing roller and other operating mechanisms for maintenance, cleaning and adjustment, please be sure to lock the safety lock to ensure that each mechanism will not fall or close on its own and cause personal injury.

3. When the header is blocked, adjust the gap between the moving and fixed blades to about 0.3~1mm; if the cutter blade or blade protector is damaged, the blade or blade protector needs to be replaced. When stacking crops on the header, the gap between the header feeding auger and the header bottom plate should be adjusted to about 6~15mm. When feeding the whurling dragon and wrapping the grass, the paddle on the right side of the whurling dragon should be adjusted to make the gap between the tooth rod and the bottom plate 6~10mm. When the reel has more seeds, the speed of the reel needs to be reduced.

4. When the threshing cylinder is blocked, the belt tension can be adjusted to ensure the rotation speed of the cylinder. If the feeding amount is too large, the forward speed of the machine can be reduced or the cutting stubble can be increased. When the grass is discharged and the grains are too high, the blockage of the "dead corners" before and after the concave screen must be cleaned, the engine speed reaches 2500 r/min, and the accelerator must be stepped in place. When the impurity content rate in grain is high, the angle of fish scale screen should be adjusted to the appropriate position, the air volume adjustment plate should be adjusted, and the air intake should be appropriately increased.

(III) safety operation tips,

1. Do not operate and maintain the harvester after drinking, taking medicine or under fatigue.

2. Be sure to shut down the engine and remove the key when cleaning, overhauling, refueling and when the operator leaves the cab.

3. When two people jointly overhaul the harvester, it is strictly forbidden for another person to rotate the rotating parts without permission.

4. When lifting the header, opening the granary, threshing roller and other operating mechanisms for maintenance, cleaning and adjustment, please be sure to lock the safety lock to ensure that each mechanism will not fall or close on its own and cause personal injury.

5. It is strictly prohibited to smoke in rice (wheat) fields, and to prevent fire safety accidents caused by poor contact of electrical circuits, short circuits, and accumulation of grass clippings around engine exhaust pipes.

Source: Public Number Sangma Words Liangzhou

Website: https://mp.weixin.qq.com/s/ZTSndPLw1mcZo3Bfs2hvUA


收获机械培训维修

Created on:2025-09-11

Self-walking Crawler Grain Combine Harvester Maintenance Points

self-walking crawler grain combine harvesterMaintenance points

Maintenance before (I) operation

1. Clean the engine air filter and air duct; clean or replace the oil filter element and diesel filter element and replace the oil pan oil, hydraulic oil, and brake fluid; fill the fuel tank with qualified diesel; add coolant; check the battery power And charge. Start the engine, idling for 10~15 minutes, and observe whether there is any abnormality. If there is any abnormality, stop the engine for inspection and elimination.

2. Check the bolt tightening of the roller, fan, header, screen box drive mechanism and other parts with high speed, heavy vibration and heavy load, and the sprocket and bearing with high speed, and adjust as required.

3. Check whether the rotating parts rotate flexibly; adjust the tension of the chain and transmission belt.

4. Inspect the harvesting mechanism. Check whether the cutter blade is intact and firm, whether the gap is reasonable, whether the center line of the moving blade and the blade protector is coincident, and adjust the fastening as required; adjust the height of the reel and the sagging amount of the holding claw according to the operation requirements.

5. Check the threshing and cleaning device. Adjust the threshing clearance and cleaning fan air volume according to the operation requirements. Check the wear of the grass cutter, vibrating screen and front bearing, louver sieve strip, etc. and replace them as necessary.

6. Check the straw handling mechanism. First, adjust the straw discharge position to ensure uniform discharge of straw when feeding the harvester. Second, check whether the cutting knife and fixed knife are worn or damaged, and replace with new blades if any. When the overlap between the cutter blade of the semi-feeding harvester and the supply knife blade is less than 9mm, the installation position of the supply knife shaft shall be adjusted. The gap between the cutter blade and the supply knife blade should be between 4.5~7mm; The gap between the straw chain pressure rod and the sprocket should be adjusted to within 2.5mm.

7. Check the technical status of clutches and brakes to see their reliability and flexibility.

8. Check the hydraulic oil pump, control valve and pipeline. If it is damaged, it should be replaced in time. If the hydraulic oil is too dirty and has impurities, it should be replaced.

9. Check the sealing of the joint between the bridge and the concave plate transition plate of the threshing roller to reduce the harvest loss and prevent the phenomenon of grain running and grain leakage.

(II) operation

1. The engine oil and oil filter must be replaced every 250 to 300 hours of operation, and the diesel filter must be replaced every 200 hours of operation; the hydraulic system must be replaced every 250 to 300 hours of operation. Oil change and oil return filter, walking filter element once. Be sure to shut down the engine before cleaning, overhaul, maintenance, refueling and before the operator leaves the cab.

2. Before lifting the header, opening the granary, threshing roller and other operating mechanisms for maintenance, cleaning and adjustment, please be sure to lock the safety lock to ensure that each mechanism will not fall or close on its own and cause personal injury.

3. When the header is blocked, adjust the gap between the moving and fixed blades to about 0.3~1mm; if the cutter blade or blade protector is damaged, the blade or blade protector needs to be replaced. When stacking crops on the header, the gap between the header feeding auger and the header bottom plate should be adjusted to about 6~15mm. When feeding the whurling dragon and wrapping the grass, the paddle on the right side of the whurling dragon should be adjusted to make the gap between the tooth rod and the bottom plate 6~10mm. When the reel has more seeds, the speed of the reel needs to be reduced.

4. When the threshing cylinder is blocked, the belt tension can be adjusted to ensure the rotation speed of the cylinder. If the feeding amount is too large, the forward speed of the machine can be reduced or the cutting stubble can be increased. When the grass is discharged and the grains are too high, the blockage of the "dead corners" before and after the concave screen must be cleaned, the engine speed reaches 2500 r/min, and the accelerator must be stepped in place. When the impurity content rate in grain is high, the angle of fish scale screen should be adjusted to the appropriate position, the air volume adjustment plate should be adjusted, and the air intake should be appropriately increased.

(III) safety operation tips,

1. Do not operate and maintain the harvester after drinking, taking medicine or under fatigue.

2. Be sure to shut down the engine and remove the key when cleaning, overhauling, refueling and when the operator leaves the cab.

3. When two people jointly overhaul the harvester, it is strictly forbidden for another person to rotate the rotating parts without permission.

4. When lifting the header, opening the granary, threshing roller and other operating mechanisms for maintenance, cleaning and adjustment, please be sure to lock the safety lock to ensure that each mechanism will not fall or close on its own and cause personal injury.

5. It is strictly prohibited to smoke in rice (wheat) fields, and to prevent fire safety accidents caused by poor contact of electrical circuits, short circuits, and accumulation of grass clippings around engine exhaust pipes.

Source: Public Number Sangma Words Liangzhou

Website: https://mp.weixin.qq.com/s/ZTSndPLw1mcZo3Bfs2hvUA