China-Brazil Agricultural Mechanization Advanced Technology and Equipment Exhibition and Cooperation Platform
China - Brazil agricultural mechanization advanced applicable technology and equipment exhibition and cooperation platform
(II)
-transplanter maintenance
1, clean the machine. Clean the body, remove foreign matter and entanglement; clean the air filter, radiator and oil-water separator.
2. Check and add fuel and coolant (water). Fill fuel, clean or replace the fuel filter element according to the operating hours specified in the manual; check, supplement or replace the engine, gearbox, rear axle box, planting box and other parts of the engine, gearbox, rear car axle box, and replace the oil filter element at the same time. Check whether the engine air filter, the joint surface of the cylinder block and the cylinder head, etc. are leaking, the joint surfaces of the engine oil pan, gearbox, working transmission box, chain box, etc. are not leaking, and the oil plugs, planting arms, etc. are not leaking oil.
3. Fill lubricating grease. According to the requirements of the manual, apply or add lubricating grease to the planting arm, rotating box, moving bracket, pontoon, connecting rod, drive shaft, slider, guide rail, clutch and other parts.
4. Inspection of important parts and components. Check whether the main nuts of the external and connecting parts are abnormal or loose, and if necessary, adjust and tighten them. Check the wear of front and rear tires; Check, adjust or replace the engine belt, gearbox drive belt and longitudinal conveyor belt; Check and adjust the handles, pull rods and pull wires; Check or replace the seedling pusher and seedling needle; Check and adjust the amount of seedlings to meet the technical requirements; Check and supplement the battery power.
5, start-up inspection. Check whether the starting motor, generator, horn, lamp and other electrical components are normal, whether the engine has abnormal noise, whether the exhaust smoke color is normal, whether the instrument indication is normal, etc., and repair in time if any fault is found; manually rotate the working part to make the main clutch In the engaged state, set the gear shift handle to neutral, slowly shake the engine with the hand handle (do not start), and check the operation of the working part in combination with the rice transplanter clutch, there should be no phenomenon such as the planting arm jamming the seedling door; pull the transplanting clutch handle to the away position, pull up the decompression handle, and shake the handle by hand. The hand sensing is easy and flexible when shaking, and the fuel injection nozzle should be heard when it is fast. Sound, while accelerating the shaking, quickly lower the decompression handle, and the diesel engine will start running immediately. After the engine runs smoothly, make the working part of the transplanter idle for 10 minutes with medium and slow speed, and test run for 30 minutes with transplanting speed and walking speed. When the diesel engine is running, there is no abnormal sound such as cylinder knocking and tooth beating. The diesel engine speed is stable, no black smoke, no oil, and no resonance.
6. Operation inspection. Check whether the seedling loading platform, seedling feeding parts, planting arm and other planting parts work normally. The steering wheel should be flexible and the free stroke should be accurate. The maximum angle of left and right steering is 60 degrees; The free stroke of the foot pedal of the crossing device should be correct. When stepping on the foot pedal, the ship plate should be lifted with the hanging chain. When the foot pedal is released, the ship plate should return to its original position. All operating mechanisms are reliably engaged, with the help of the clutch, the gear should be flexible and reliable, and the gear should be picked up smoothly, without shifting, skipping, etc., and no abnormal sounds such as tooth beating; the planting positioning clutch should be accurate and reliable, and the correct position is: when pulling down the planting positioning clutch, the planting arm Should stop above the seedling door. During the operation of the planting arm, it is not allowed to touch any relevant parts; The change of the seedling box is accurate. When the seedling box moves to the left and right limit positions, the lateral displacement of the finger pin in the spiral groove stops, and the change is completed by the smooth transition surface of the 180 straight groove and the spiral groove. At the same time, the seedling feeding belt should rotate for a certain distance. The safety clutch shall be automatically separated when it is blocked. The rotation should be flexible: When the lifting rod rotates, the height of the chain box relative to the seedling boat can be changed, thus changing the transplanting height of the planting arm, so as to achieve the purpose of adjusting the transplanting depth. During the operation of the holding mechanism, it is necessary to see if there is any phenomenon that 6 or 8 groups of planting arms do not push seedlings.
7, walking inspection. Start slowly, check whether the transplanter runs smoothly, whether the brake and transmission work normally, etc., and repair the fault in time.