Created on:2023-08-26

Tractor and Rotary Tiller

dragPulling Machine and Rotary Tiller

1. tractors

(I) inspection of each component

1. Tighten the connecting pieces of each part: although the tractor has been inspected by the factory when it leaves the factory, it is inevitable that the machine will be connected loosely in the process of repeated transportation. For this reason, various connectors and fasteners should be tightened in time, especially the steering system, brake system, suspension and wheels.

2. Check the liquid level: mainly the fuel tank oil level, water tank water level, transmission and rear axle lubricating oil level, and battery electrolyte level. When the liquid level is insufficient, the liquid material should be added in time.

3. Check the oil:(1) The amount of oil in the oil pan should not be less than the engraved line under the oil dipstick. (2) The quality of the oil: If the tractor is in summer when it leaves the factory, and it is winter when it is bought back, it should be replaced with winter oil; and vice versa. (3) The changeover switch of the oil filter on the large tractor should be turned to the summer or winter position according to the season or temperature. (4) In order to prevent the oil in the oil pan of the oil-bath air filter from spilling out and polluting the vehicle capacity during transportation, some manufacturers add it at the end of the factory, and pay attention to adding oil after buying it.

4. Listing: After the new tractor is bought back. Should carry the purchase invoice, certificate, instruction manual and other documents within 3 months, to the agricultural machinery, levy and other departments for household registration procedures. Driving on the road without a license is illegal and will be punished.

(II) do a good job in the running-in of the tractor.

new tractors must be run-in before they start to use. Running-in is an important means to extend the service life of tractors. Because the parts after processing, the surface contains different degrees of knife marks, if you put into heavy load operation without running in, the uneven friction surface of the parts will be damaged quickly, which greatly enhances the wear of the parts, thus shortening the service life of the tractor. The purpose of running-in is to make the uneven friction surface gradually grinding smooth, to obtain a smooth and hard bearing surface, but also to get the most suitable clearance, so that the tractor into normal operation, can withstand the load, and to extend the service life to lay a good foundation.

Tractor running-in should follow the following procedures:

1. Engine idling running-in: After the engine is started, let the engine idle for 5 minutes, and then gradually increase to the calibrated speed for idle running. Engine idling running-in time should generally be about 15 minutes.

2. Running-in of hydraulic system. Start the engine, operate the lifter handle to lift and lower the suspension mechanism several times, observe whether the hydraulic system has the phenomenon of top jam and suction, then hang farm tools or weights with a weight less than 500kg, and operate the lifter handle at the engine calibration speed, Make the farm tools lift and lower smoothly, the number of times is not less than 50 times. If the tractor is hydraulically steered, the engine runs at three speeds of low, medium and high when the tractor is stationary, and the steering wheel is operated to see if it is light and stable.

3. Tractor idle running-in: In the idle running-in process, the engine speed should be controlled at about 1500 r/min minutes, and the speed should be carried out from low to high gear step by step. Finally, reverse gear running-in should be carried out. The tractor idle running-in time should be about 5 hours.

4. Tractor load running-in: Tractor load running-in is to bring a certain load to run, running-in principle is: the load from small to large gradually increase, speed from low to high gear. The specific operation method varies from car to car. Please refer to the load running-in comparison table in the instruction manual. Generally, the running-in time should be more than 50 hours. When running-in, it must be carried out in strict accordance with the requirements of the instruction manual, and it is not necessary to reduce the running-in link or shorten the running-in time for fear of trouble.

5. Maintenance after running-in: After running-in, there will be some metal powder or dirt mixed in the lubricating oil in the transmission system, lubrication system and hydraulic system. Therefore, it is necessary to clean and replace all the lubricating oil and hydraulic oil. When replacing, the lubricating oil and hydraulic oil should be released while it is hot after the flameout and shutdown, and new lubricating oil and hydraulic oil should be added according to the regulations after cleaning. In the replacement of lubricating oil hydraulic oil at the same time should be in accordance with the provisions of cleaning or replacement of the respective filter. In addition, the necessary maintenance and adjustment of the tractor must be carried out according to the requirements of the instruction manual.

(III) do a good job in the technical maintenance of tractors

1. Shift technical maintenance and accumulated working hours technical maintenance. Shift maintenance is carried out at the beginning and end of each shift, mainly including auscultation of engine for abnormal phenomena, inspection of instruments, removal of dust and dirt; inspection of engine oil pan and transmission box oil level, insufficient addition; inspection of front and rear hub nuts Loose, check and tighten bolts and nuts of key parts such as brakes and steering gears; check the air filter to remove dust; add grease to each lubrication point according to the lubrication table, when filling, squeeze out all mud and water until the cleaning grease overflows; check the liquid level of the water tank and fuel tank, and add any shortage in time. Accumulated working time technical maintenance is divided into multiple levels. After reaching a certain working time, this level of maintenance should be carried out. The maintenance items should be carried out according to the requirements of tractor operating instructions.

2. Use clean oil. Fuel should go to a reputable gas station to buy diesel oil that meets the national standard. The diesel oil can only be used after 24 hours of precipitation. The precipitation cup should be cleaned frequently. Use 0 diesel in summer, and replace -10, -20 or -35 diesel in winter according to temperature changes. Lubricating oil and hydraulic oil must be filled with the number plate and grade that meet the requirements. The transmission hydraulic dual-purpose oil must be deposited for at least 48 hours before it can be used. It is strictly prohibited to mix diesel engine oils of different brands and manufacturers.

3. Do a good job in the maintenance of tractor storage period. Farmland operations are seasonal, and tractors are often stored for a long time after the end of an operating season. Maintenance during storage is extremely important to maintain a good technical condition. After the end of the working season, drain the engine oil while the engine is hot, replace with new engine oil, and turn off the engine after running for a few minutes at the low throttle. Fill the fuel tank with diesel oil, clean and maintain the air filter, and discharge cooling water in winter. Put all the control handles in the neutral position, adjust the front wheel and suspension rod of the tractor to the lowest position, remove the battery and place it in a ventilated room with no less than 10 ℃, it should be checked once a month, and supplementary charging should be carried out if necessary; pad the front and rear axles of the tractor, make the tires slightly off the ground, and release the tires. In addition, it is necessary to check and adjust the valve clearance, fuel supply time, clutch stroke, etc. in accordance with the requirements of the tractor's instruction manual, so that the tractor is always in a good technical condition.

2. Rotary Tiller

1. Blade installation. (1) regular operations. The entire knife shaft on the left and right machetes cross installation, this arrangement method plowed after the ground level, suitable for flat. (2) Combined operation of rotary tillage and ditching. Starting from the middle of the knife shaft, the left machete is fully installed to the left, and the right machete is fully installed to the right, with the exception of one piece at each end; Install one piece of left and one piece of right blade on the middle knife seat, so that the soil clod is thrown on both sides of the ditch to form a shallow ditch. (3) Plowing and turning fields. Starting from the middle of the knife shaft, the right machete is fully installed to the left, the left machete is fully installed to the right, and the left and right blades are installed on the middle knife seat. When the machine is operating across the ditch, the soil clod is thrown into the ditch to fill the ditch.

2. Adjust the rotary tiller before tillage. Before starting the tractor, the clutch handle of the rotary tiller should be set to the separated position. (1) left and right horizontal adjustment. Lower the rotary tiller so that the tip of the knife is close to the ground to see if the height of the left and right tips from the ground is consistent. If not, the right suspension rod can be adjusted to make the rotary tiller horizontal to ensure that the left and right tillage depth is consistent. (2) before and after the horizontal adjustment. When it is reduced to the required ploughing depth, check whether the front and rear of the drive shaft are level and whether the included angle is consistent; or whether the gearbox is level, the upper tie rod can be used to adjust the front and rear level to ensure that the drive shaft is in good working condition. (3) Lifting height adjustment. In order to ensure that the inclination angle of the transmission shaft does not exceed 25 degrees, the rotary tiller should not be lifted too high. When working in the field, it is only necessary to lift the tip of the knife to 20cm from the ground, and tighten the limit with a screw on the position adjustment handle to ensure safety.

3. Selection of farming routes in the field. (1) Flat. In order to reduce the empty row time of the land, the use of community farming method, the width of the community should be as close as possible to an integer multiple of the tillage width, in order to reduce heavy farming. (2) Ditching and furrow. Generally, from the middle of the field to the left and right, we should pay attention to walking straight. The head of the cultivated land is the same as that of the flat land. Finally, people and livestock are used to assist in opening the ditches.

4. Operation of rotary tiller. 1) Start. When the rotary tiller is raised, engage the power output shaft, engage the working gear, slowly loosen the clutch pedal, and slowly increase the throttle. After the rotary tiller reaches the predetermined speed, operate the hydraulic lifting handle to slowly lower the rotary tiller., Make the rotary tiller gradually into the soil, and then increase the throttle until the normal tillage depth. (2) Turn and reverse. The rotary tiller must be raised and cannot continue to operate. When the power is not cut off, the rotary tiller must not be raised too high, the transmission angle at both ends of the universal joint must not exceed 30 degrees, and the engine speed should be appropriately reduced. When transferring plots or walking long distances, the power of the rotary tiller should be cut off and locked after rising to the highest position.

5. Farming. When the rotary tiller is working, the tractor wheel shall walk on the uncultivated land to avoid compaction of the cultivated land. Therefore, the tractor wheel distance shall be adjusted to make the wheel within the working width of the rotary tiller. Pay attention to the walking method during operation to prevent the other wheel of the tractor from compacting the cultivated land. The speed of progress during farming is 2~3 km/h in dry land, 5~7 km/h in plowed or raked land, and farming in paddy fields can be faster. Remember, the speed can not be too high, in order to prevent the tractor overload and damage the power output shaft.

6. Maintenance. (1) shift maintenance: under normal circumstances, shift maintenance should be carried out after each shift. The contents include removing soil and weeds on the blade, checking whether the vulnerable parts such as bolts and split pins are defective, and replacing them if necessary; filling lubricating oil to each lubricating oil point and filling butter to the universal joint to prevent aggravation of wear. (2) Quarterly maintenance: after the completion of each operation quarter, quarterly maintenance shall be carried out, including: thoroughly removing mud, dust and oil stains on machines and tools; Completely replace lubricating oil and grease; Check whether the blade is excessively worn and replace it if necessary; Check whether the hood and carriage plate are deformed or not, if so, restore the original shape or replace them. Comprehensively check the appearance of the machines and tools, repaint, scimitar and spline shaft should be coated with oil to prevent rust; When not used for long time, wheeled tractor supporting rotary tiller should be placed on the level of the ground, not hanging on the tractor.

7. Other Precautions. (1) It is strictly prohibited to start directly under the condition of rotary tillage knife entering the soil (2) It is strictly prohibited to descend the rotary tillage machine rapidly to prevent damage to the rotary tillage knife and related parts. (3) When the rotary tiller is running, people are strictly prohibited from approaching the rotating parts, and no one is allowed behind the rotary tiller, in case the blade is thrown out and hurt people. (4) When checking the rotary tiller, the power must be cut off first. When replacing rotating parts such as blades, the tractor must be turned off. (5) During the operation, if the knife shaft is too much wrapped with grass, it should be stopped in time to avoid increasing the load of the machine. (6) During rotary tillage, the tractor and suspension parts are not allowed to take people to prevent accidental injury by the rotary tiller.

concerned about the nine effective custody of idle agricultural machinery

entering the winter slack season, most of the agricultural machinery will be idle throughout the winter. In order to ensure that in the busy farming season in the coming year, all kinds of machinery can still maintain a good technical condition, remind the majority of farmers friends, in the winter when the agricultural machinery is idle, should pay attention to the custody of agricultural machinery.

(1) Before the machinery is put into storage, the sundries on various parts of the machine body shall be removed, especially the weeds and mud blocks on the transmission parts and moving parts, and the metal surfaces such as the transmission parts and the joysticks shall be coated with anti-rust oil.

(2) machinery should be parked in dry, ventilated ground, conditional best parked in the hangar, in order to prevent the sun, rain. If there are no conditions can only be placed outdoors, then it should be placed in a ventilated, dry and away from the fire source, near the machinery is strictly prohibited to pile up chemical fertilizers, pesticides and other corrosive chemicals. In addition, be sure to pay attention to the awning or rain protection to ensure that the fuselage is not eroded by rain and snow.

(3) Remove the intake pipe, add an appropriate amount of the above-mentioned oil from the intake pipe to each cylinder, and then rotate the crankshaft to make the oil adhere to the piston, piston ring, cylinder liner and valve sealing surface.

(4) Add grease to each grease fitting and keep the surface of the grease fitting clean.

(5) Loosen the generator belt, remove the battery, and keep it separately.

(6) The tires should be kept at normal air pressure and cushioned with cushions to make the tires hang in the air. The tires should not be stained with diesel or lubricating oil.

(7) Remove each drive belt and keep it separately.

(8) After shutdown, drain the engine oil, the cooling water in the body water jacket and the water pump housing while it is hot to remove the dust on the air filter element; the oil-bath air filter element should be cleaned with diesel or kerosene Clean.

(9) Clean the machine body, oil pan and oil strainer, and replace with new oil of corresponding brand. When changing the oil, add it to the oil pan to the upper engraved line of the oil gauge and rotate the crankshaft to fill the entire lubrication system with oil.

Wheat Combine Maintenance Seven Attention

wheat combine harvester will inevitably malfunction when working, so in the whole process of wheat harvest, wheat combine harvester maintenance is particularly important. In the maintenance should pay attention to a few points:

1. Riveted parts in the harvester. Such as moving knife assembly, rivets are generally cold extrusion, in the riveting should not be heated, such as heating will reduce the strength of the material. After riveting, a forming punch shall be applied to strengthen the firmness of the blade and the cutter bar.

2. Vulnerable parts, especially pin shaft, pressing sheet, sleeve and shim. In the maintenance can not be used to add more butter instead of replacement and repair, such as long-term use of wear to the limit of parts will cause other mechanical life reduction.

3, no balance machine shaft repair. When repairing various shafts that need to be balanced, a thrust bearing can be installed at one end of the shaft and clamped on the three claws of the lathe, and the other end can be supported by the top. If the lathe is short, the center frame can be used to clamp the bearing installed on the other end of the shaft and correct the balance. But in the counterweight, with the screw tight, try not to use electric welding counterweight.

4. In the maintenance, due to the variety of materials, it is not easy to purchase, and waste shafts can be used for processing. At present, most shafts in our country are mainly made of 45# carbon steel. If quenching and tempering are required, under bad conditions, oxygen and earth furnace can be used to heat the required parts into red, black and black brine, depending on the demand.

5. Pull the oil groove in the sleeve hole as much as possible when processing sleeve parts. Because it is very difficult to refuel some parts of the harvester, butter and heavy oil can be used where it is difficult to refuel, except for nylon sleeves. Where the nylon sleeve is used, it is best not to use cast iron, copper, aluminum instead, because the nylon sleeve bears a certain impact without deformation.

6. Key and keyway repair on pulley and shaft. It should be ensured that the size does not change to advance, and the size of the key must not be increased, otherwise the strength of the shaft will be affected. The key groove on the shaft can be milled in the opposite direction of the old key by electric welding filler. The key groove on the pulley can be inserted by sleeve (transition fit). After being inserted, the key can be inserted tightly in the sleeve seam with countersunk screws.

7, the maintenance of the hydraulic part of the harvester. Remove the distributor and reducing valve, etc., use the air pump to pressure the pipe fittings, filter and exhaust the hydraulic oil when it is loaded twice, and the maintenance of the assembly hydraulic pressure is mainly the seal, and the seal is best replaced after removing.

培训维修

Created on:2023-08-26

Tractor and Rotary Tiller

dragPulling Machine and Rotary Tiller

1. tractors

(I) inspection of each component

1. Tighten the connecting pieces of each part: although the tractor has been inspected by the factory when it leaves the factory, it is inevitable that the machine will be connected loosely in the process of repeated transportation. For this reason, various connectors and fasteners should be tightened in time, especially the steering system, brake system, suspension and wheels.

2. Check the liquid level: mainly the fuel tank oil level, water tank water level, transmission and rear axle lubricating oil level, and battery electrolyte level. When the liquid level is insufficient, the liquid material should be added in time.

3. Check the oil:(1) The amount of oil in the oil pan should not be less than the engraved line under the oil dipstick. (2) The quality of the oil: If the tractor is in summer when it leaves the factory, and it is winter when it is bought back, it should be replaced with winter oil; and vice versa. (3) The changeover switch of the oil filter on the large tractor should be turned to the summer or winter position according to the season or temperature. (4) In order to prevent the oil in the oil pan of the oil-bath air filter from spilling out and polluting the vehicle capacity during transportation, some manufacturers add it at the end of the factory, and pay attention to adding oil after buying it.

4. Listing: After the new tractor is bought back. Should carry the purchase invoice, certificate, instruction manual and other documents within 3 months, to the agricultural machinery, levy and other departments for household registration procedures. Driving on the road without a license is illegal and will be punished.

(II) do a good job in the running-in of the tractor.

new tractors must be run-in before they start to use. Running-in is an important means to extend the service life of tractors. Because the parts after processing, the surface contains different degrees of knife marks, if you put into heavy load operation without running in, the uneven friction surface of the parts will be damaged quickly, which greatly enhances the wear of the parts, thus shortening the service life of the tractor. The purpose of running-in is to make the uneven friction surface gradually grinding smooth, to obtain a smooth and hard bearing surface, but also to get the most suitable clearance, so that the tractor into normal operation, can withstand the load, and to extend the service life to lay a good foundation.

Tractor running-in should follow the following procedures:

1. Engine idling running-in: After the engine is started, let the engine idle for 5 minutes, and then gradually increase to the calibrated speed for idle running. Engine idling running-in time should generally be about 15 minutes.

2. Running-in of hydraulic system. Start the engine, operate the lifter handle to lift and lower the suspension mechanism several times, observe whether the hydraulic system has the phenomenon of top jam and suction, then hang farm tools or weights with a weight less than 500kg, and operate the lifter handle at the engine calibration speed, Make the farm tools lift and lower smoothly, the number of times is not less than 50 times. If the tractor is hydraulically steered, the engine runs at three speeds of low, medium and high when the tractor is stationary, and the steering wheel is operated to see if it is light and stable.

3. Tractor idle running-in: In the idle running-in process, the engine speed should be controlled at about 1500 r/min minutes, and the speed should be carried out from low to high gear step by step. Finally, reverse gear running-in should be carried out. The tractor idle running-in time should be about 5 hours.

4. Tractor load running-in: Tractor load running-in is to bring a certain load to run, running-in principle is: the load from small to large gradually increase, speed from low to high gear. The specific operation method varies from car to car. Please refer to the load running-in comparison table in the instruction manual. Generally, the running-in time should be more than 50 hours. When running-in, it must be carried out in strict accordance with the requirements of the instruction manual, and it is not necessary to reduce the running-in link or shorten the running-in time for fear of trouble.

5. Maintenance after running-in: After running-in, there will be some metal powder or dirt mixed in the lubricating oil in the transmission system, lubrication system and hydraulic system. Therefore, it is necessary to clean and replace all the lubricating oil and hydraulic oil. When replacing, the lubricating oil and hydraulic oil should be released while it is hot after the flameout and shutdown, and new lubricating oil and hydraulic oil should be added according to the regulations after cleaning. In the replacement of lubricating oil hydraulic oil at the same time should be in accordance with the provisions of cleaning or replacement of the respective filter. In addition, the necessary maintenance and adjustment of the tractor must be carried out according to the requirements of the instruction manual.

(III) do a good job in the technical maintenance of tractors

1. Shift technical maintenance and accumulated working hours technical maintenance. Shift maintenance is carried out at the beginning and end of each shift, mainly including auscultation of engine for abnormal phenomena, inspection of instruments, removal of dust and dirt; inspection of engine oil pan and transmission box oil level, insufficient addition; inspection of front and rear hub nuts Loose, check and tighten bolts and nuts of key parts such as brakes and steering gears; check the air filter to remove dust; add grease to each lubrication point according to the lubrication table, when filling, squeeze out all mud and water until the cleaning grease overflows; check the liquid level of the water tank and fuel tank, and add any shortage in time. Accumulated working time technical maintenance is divided into multiple levels. After reaching a certain working time, this level of maintenance should be carried out. The maintenance items should be carried out according to the requirements of tractor operating instructions.

2. Use clean oil. Fuel should go to a reputable gas station to buy diesel oil that meets the national standard. The diesel oil can only be used after 24 hours of precipitation. The precipitation cup should be cleaned frequently. Use 0 diesel in summer, and replace -10, -20 or -35 diesel in winter according to temperature changes. Lubricating oil and hydraulic oil must be filled with the number plate and grade that meet the requirements. The transmission hydraulic dual-purpose oil must be deposited for at least 48 hours before it can be used. It is strictly prohibited to mix diesel engine oils of different brands and manufacturers.

3. Do a good job in the maintenance of tractor storage period. Farmland operations are seasonal, and tractors are often stored for a long time after the end of an operating season. Maintenance during storage is extremely important to maintain a good technical condition. After the end of the working season, drain the engine oil while the engine is hot, replace with new engine oil, and turn off the engine after running for a few minutes at the low throttle. Fill the fuel tank with diesel oil, clean and maintain the air filter, and discharge cooling water in winter. Put all the control handles in the neutral position, adjust the front wheel and suspension rod of the tractor to the lowest position, remove the battery and place it in a ventilated room with no less than 10 ℃, it should be checked once a month, and supplementary charging should be carried out if necessary; pad the front and rear axles of the tractor, make the tires slightly off the ground, and release the tires. In addition, it is necessary to check and adjust the valve clearance, fuel supply time, clutch stroke, etc. in accordance with the requirements of the tractor's instruction manual, so that the tractor is always in a good technical condition.

2. Rotary Tiller

1. Blade installation. (1) regular operations. The entire knife shaft on the left and right machetes cross installation, this arrangement method plowed after the ground level, suitable for flat. (2) Combined operation of rotary tillage and ditching. Starting from the middle of the knife shaft, the left machete is fully installed to the left, and the right machete is fully installed to the right, with the exception of one piece at each end; Install one piece of left and one piece of right blade on the middle knife seat, so that the soil clod is thrown on both sides of the ditch to form a shallow ditch. (3) Plowing and turning fields. Starting from the middle of the knife shaft, the right machete is fully installed to the left, the left machete is fully installed to the right, and the left and right blades are installed on the middle knife seat. When the machine is operating across the ditch, the soil clod is thrown into the ditch to fill the ditch.

2. Adjust the rotary tiller before tillage. Before starting the tractor, the clutch handle of the rotary tiller should be set to the separated position. (1) left and right horizontal adjustment. Lower the rotary tiller so that the tip of the knife is close to the ground to see if the height of the left and right tips from the ground is consistent. If not, the right suspension rod can be adjusted to make the rotary tiller horizontal to ensure that the left and right tillage depth is consistent. (2) before and after the horizontal adjustment. When it is reduced to the required ploughing depth, check whether the front and rear of the drive shaft are level and whether the included angle is consistent; or whether the gearbox is level, the upper tie rod can be used to adjust the front and rear level to ensure that the drive shaft is in good working condition. (3) Lifting height adjustment. In order to ensure that the inclination angle of the transmission shaft does not exceed 25 degrees, the rotary tiller should not be lifted too high. When working in the field, it is only necessary to lift the tip of the knife to 20cm from the ground, and tighten the limit with a screw on the position adjustment handle to ensure safety.

3. Selection of farming routes in the field. (1) Flat. In order to reduce the empty row time of the land, the use of community farming method, the width of the community should be as close as possible to an integer multiple of the tillage width, in order to reduce heavy farming. (2) Ditching and furrow. Generally, from the middle of the field to the left and right, we should pay attention to walking straight. The head of the cultivated land is the same as that of the flat land. Finally, people and livestock are used to assist in opening the ditches.

4. Operation of rotary tiller. 1) Start. When the rotary tiller is raised, engage the power output shaft, engage the working gear, slowly loosen the clutch pedal, and slowly increase the throttle. After the rotary tiller reaches the predetermined speed, operate the hydraulic lifting handle to slowly lower the rotary tiller., Make the rotary tiller gradually into the soil, and then increase the throttle until the normal tillage depth. (2) Turn and reverse. The rotary tiller must be raised and cannot continue to operate. When the power is not cut off, the rotary tiller must not be raised too high, the transmission angle at both ends of the universal joint must not exceed 30 degrees, and the engine speed should be appropriately reduced. When transferring plots or walking long distances, the power of the rotary tiller should be cut off and locked after rising to the highest position.

5. Farming. When the rotary tiller is working, the tractor wheel shall walk on the uncultivated land to avoid compaction of the cultivated land. Therefore, the tractor wheel distance shall be adjusted to make the wheel within the working width of the rotary tiller. Pay attention to the walking method during operation to prevent the other wheel of the tractor from compacting the cultivated land. The speed of progress during farming is 2~3 km/h in dry land, 5~7 km/h in plowed or raked land, and farming in paddy fields can be faster. Remember, the speed can not be too high, in order to prevent the tractor overload and damage the power output shaft.

6. Maintenance. (1) shift maintenance: under normal circumstances, shift maintenance should be carried out after each shift. The contents include removing soil and weeds on the blade, checking whether the vulnerable parts such as bolts and split pins are defective, and replacing them if necessary; filling lubricating oil to each lubricating oil point and filling butter to the universal joint to prevent aggravation of wear. (2) Quarterly maintenance: after the completion of each operation quarter, quarterly maintenance shall be carried out, including: thoroughly removing mud, dust and oil stains on machines and tools; Completely replace lubricating oil and grease; Check whether the blade is excessively worn and replace it if necessary; Check whether the hood and carriage plate are deformed or not, if so, restore the original shape or replace them. Comprehensively check the appearance of the machines and tools, repaint, scimitar and spline shaft should be coated with oil to prevent rust; When not used for long time, wheeled tractor supporting rotary tiller should be placed on the level of the ground, not hanging on the tractor.

7. Other Precautions. (1) It is strictly prohibited to start directly under the condition of rotary tillage knife entering the soil (2) It is strictly prohibited to descend the rotary tillage machine rapidly to prevent damage to the rotary tillage knife and related parts. (3) When the rotary tiller is running, people are strictly prohibited from approaching the rotating parts, and no one is allowed behind the rotary tiller, in case the blade is thrown out and hurt people. (4) When checking the rotary tiller, the power must be cut off first. When replacing rotating parts such as blades, the tractor must be turned off. (5) During the operation, if the knife shaft is too much wrapped with grass, it should be stopped in time to avoid increasing the load of the machine. (6) During rotary tillage, the tractor and suspension parts are not allowed to take people to prevent accidental injury by the rotary tiller.

concerned about the nine effective custody of idle agricultural machinery

entering the winter slack season, most of the agricultural machinery will be idle throughout the winter. In order to ensure that in the busy farming season in the coming year, all kinds of machinery can still maintain a good technical condition, remind the majority of farmers friends, in the winter when the agricultural machinery is idle, should pay attention to the custody of agricultural machinery.

(1) Before the machinery is put into storage, the sundries on various parts of the machine body shall be removed, especially the weeds and mud blocks on the transmission parts and moving parts, and the metal surfaces such as the transmission parts and the joysticks shall be coated with anti-rust oil.

(2) machinery should be parked in dry, ventilated ground, conditional best parked in the hangar, in order to prevent the sun, rain. If there are no conditions can only be placed outdoors, then it should be placed in a ventilated, dry and away from the fire source, near the machinery is strictly prohibited to pile up chemical fertilizers, pesticides and other corrosive chemicals. In addition, be sure to pay attention to the awning or rain protection to ensure that the fuselage is not eroded by rain and snow.

(3) Remove the intake pipe, add an appropriate amount of the above-mentioned oil from the intake pipe to each cylinder, and then rotate the crankshaft to make the oil adhere to the piston, piston ring, cylinder liner and valve sealing surface.

(4) Add grease to each grease fitting and keep the surface of the grease fitting clean.

(5) Loosen the generator belt, remove the battery, and keep it separately.

(6) The tires should be kept at normal air pressure and cushioned with cushions to make the tires hang in the air. The tires should not be stained with diesel or lubricating oil.

(7) Remove each drive belt and keep it separately.

(8) After shutdown, drain the engine oil, the cooling water in the body water jacket and the water pump housing while it is hot to remove the dust on the air filter element; the oil-bath air filter element should be cleaned with diesel or kerosene Clean.

(9) Clean the machine body, oil pan and oil strainer, and replace with new oil of corresponding brand. When changing the oil, add it to the oil pan to the upper engraved line of the oil gauge and rotate the crankshaft to fill the entire lubrication system with oil.

Wheat Combine Maintenance Seven Attention

wheat combine harvester will inevitably malfunction when working, so in the whole process of wheat harvest, wheat combine harvester maintenance is particularly important. In the maintenance should pay attention to a few points:

1. Riveted parts in the harvester. Such as moving knife assembly, rivets are generally cold extrusion, in the riveting should not be heated, such as heating will reduce the strength of the material. After riveting, a forming punch shall be applied to strengthen the firmness of the blade and the cutter bar.

2. Vulnerable parts, especially pin shaft, pressing sheet, sleeve and shim. In the maintenance can not be used to add more butter instead of replacement and repair, such as long-term use of wear to the limit of parts will cause other mechanical life reduction.

3, no balance machine shaft repair. When repairing various shafts that need to be balanced, a thrust bearing can be installed at one end of the shaft and clamped on the three claws of the lathe, and the other end can be supported by the top. If the lathe is short, the center frame can be used to clamp the bearing installed on the other end of the shaft and correct the balance. But in the counterweight, with the screw tight, try not to use electric welding counterweight.

4. In the maintenance, due to the variety of materials, it is not easy to purchase, and waste shafts can be used for processing. At present, most shafts in our country are mainly made of 45# carbon steel. If quenching and tempering are required, under bad conditions, oxygen and earth furnace can be used to heat the required parts into red, black and black brine, depending on the demand.

5. Pull the oil groove in the sleeve hole as much as possible when processing sleeve parts. Because it is very difficult to refuel some parts of the harvester, butter and heavy oil can be used where it is difficult to refuel, except for nylon sleeves. Where the nylon sleeve is used, it is best not to use cast iron, copper, aluminum instead, because the nylon sleeve bears a certain impact without deformation.

6. Key and keyway repair on pulley and shaft. It should be ensured that the size does not change to advance, and the size of the key must not be increased, otherwise the strength of the shaft will be affected. The key groove on the shaft can be milled in the opposite direction of the old key by electric welding filler. The key groove on the pulley can be inserted by sleeve (transition fit). After being inserted, the key can be inserted tightly in the sleeve seam with countersunk screws.

7, the maintenance of the hydraulic part of the harvester. Remove the distributor and reducing valve, etc., use the air pump to pressure the pipe fittings, filter and exhaust the hydraulic oil when it is loaded twice, and the maintenance of the assembly hydraulic pressure is mainly the seal, and the seal is best replaced after removing.